Cygnus Instruments Ltd is a well-known and trusted UK manufacturer of high quality ultrasonic testing equipment which is extremely durable and simple to use.
Poor maintenance of hatch covers, seals and coamings, resulting in water entering a ship’s hold, can lead to highly expensive or even devastating consequences. Testing that hatch covers are weather-tight is a fundamental requirement for preventing damage to cargo and ensuring the safety of a vessel and its crew.
Ultrasonic testing is the most accurate, repeatable and convenient method of testing hatch covers, doors, ventilators and access hatches and is the preferred method of inspection by P&I Clubs but there are others methods in use.
Hatches are fully battened down and a surveyor will view the underside of the covers to see if any visible daylight is shining through gaps. If the sunlight level is insufficient a strong torchlight will be shone directly from above instead. This is the simplest method for identifying defects and their location but it may not be so easy to identify very small gaps.
Chalk powder is applied to the coaming compression bars and panel cross seams, the hatches are then closed and re-opened. The rubber joints are carefully examined. If there are irregularities in the chalk
markings then it is assumed that these areas are not weather-tight. This method was the traditional way for testing hold cover compression but does not test the watertight integrity of the hold. IACS states that this test should be followed by a hose test.
The conventional technique for testing weather tightness of hatch covers is hose testing which uses large volumes of water sprayed at the rubber seals
The hatches are secured, with one surveyor in the hold. On deck a constant jet of pressurized water is then directed at the hatch-cover seams and joints. Any water leaking into the hold should then be seen by the Surveyor inside, indicating a defect in the seams or joints. Although the most common method of testing hatch- covers, this technique has many limitations when compared with using ultrasound:
- the hold must be empty;
- minimum of two surveyors is required; v it cannot be performed in sub-zero temperatures;
- run-off from the deck which can lead to pollution — some port authorities will not permit this;
- it cannot accurately pinpoint leakages as water might travel along drainage channels and enter the hold at a different point or travel through the drain valves and back onto deck;
- variance in water pressure and distance of the jet can affect results; and
- it is time consuming.
This is an accurate, repeatable and convenient method of testing hatch-covers, doors, ventilators, access hatches, etc.
A transmitter emitting ultrasound is placed in the hold and the hatches are then fully closed. On deck the surveyor wearing headphones will walk around the periphery of the covers using a hand-held receiver or detector and will be able to hear ultrasound leaking through any defective seams or joints — even through the smallest of openings.
A percentage scale is used with an open hatch emitting 100% of the ultrasound. DNV and ABS state that during an inspection any reading over 10% indicates an area of potential leakage.
When a vessel is at sea and is pitching and flexing, seals that were demonstrated to be tight when the ship was stationary might potential leak. A benefit of the ultrasonic method is that the level of compression of a seal can also be detected and monitored through periodic mainte- nance checks. A higher percentage reading indicates a lower level of compression and could indicate a seal which will leak when the ship is in rough conditions.
HATCH COVER TESTER
While ultrasonic hatch cover testing has been available since the 1980s, Cygnus Hatch Sure has advanced
the current technology with
fully automatic Open Hatch
Calibration (OHC) to set
the Open Hatch Value
(OHV). This ensures consis-
tent results from hold to
hold with a lightweight and
extremely powerful 19 ×
40Hz element transmitter.
This is powerful enough to
saturate the largest cargo
hold with ultrasound. The
variable output transmitter
has six selectable power
levels allowing the unit to
also be used in confined
spaces, such as for testing
watertight doors. Designed
for ease of use and powered
by standard rechargeable
batteries, the whole system
is extremely light and
aircraft friendly for passenger
The Cygnus Hatch Sure
leak detector is a purpose-
designed, robust and very lightweight system; as such it has become
the market leader for ultrasonic hatch
cover inspections and is the preferred
choice of multinational ship management
companies across the globe who want to
test covers quickly, accurately and cost
Cygnus Hatch Sure is ABS Type
Approved and accepted by all P&I Clubs. The Cygnus product training syllabus has been endorsed by the International Institute of Marine Surveyors (IIMS).
CYGNUS HATCH SURE
The Cygnus Hatch Sure
system is comprised of two
main components (see
picture, right): a powerful
ultrasound transmitter with
19 x 40 KHz elements and a
The system is used by
placing the transmitter
within the ship’s hold,
conducting a quick and
simple calibration and then
closing down the covers.
The transmitter is then
switched on remotely and it will fill the hold with ultrasound; any
ultrasound that escapes will be detected by
the operator, who will be on the deck
walking around the periphery of the covers
using the receiver. Using the sensitive
microphone attached to the receiver, the
system allows the operator to locate
ultrasound leaking through any defective seams or joints; exact locations of potential
costly leaks in heavy seas or rain are quickly
and easily identified.
Cygnus Hatch Sure is entirely designed
for ease of use and powered by standard
rechargeable batteries.The whole system is
extremely light and aircraft friendly for
passenger cabin transportation.